Відео

no power switch on your battery charger ?

can you please get to the point quickly?

Don't do as this idiot does and drain it onto the floor ! Get a bowl or container to catch the water.

Thank you 🙏 😊😊😊

thanks for posting. I have a rusty frame on a big welder and after grinding I need ti remove the rust in the pitted spots before applying an epoxy. I will use cyour recomendation.

USELESS!

Very useful. What grit aluminum oxide and glass was used for comparison? Thanks for sharing

Most examples I have seen and therefore all I have ever used involve washing soda rather than acetic acid. I would imagine an acidic solution may work quicker due to the fact that an acid can cause the iron to go into solution whereas a basic solution cannot. Then again I would imagine the basic solution may do better to preserve the most of the base material under the iron oxide and be safer for your part in restoration.

One hour! If you had let the high concentration acetic acid do its work over 24-72hrs you would see a stark difference. Why not test straight 35% acetic acid(electrolyte) and electrolysis?

Would it help if you put this in an ultrasonic cleaner?

Nice

This is the best example of thread tension on the Internet! 👏🙋🏼‍♀️

Wow pretty cool

Wonderfully done and explained in detail the entire process.

Thanks a lot, worked perfectly!

Short version: Open the flap on the front bottom edge of your machine. Put a key or flat screwdriver in the eye of black bit of plastic that points downwards and push it down. Done. Cut to 3:45 of this video if you feel the need.

Hold on now sir, I've been sewing almost 50 years, your making it harder than it is when it is basic common sense. You are trying to hide the thread twist of a very thick thread inbetween only 2 layers of a fabric weight that just is not thick enough to hide it. Drop down to a thinner thread that is appropriate for what you are sewing. If the thread used must be two different colors and certain parts of the project is only 2 layers of fabric no amount or adjustment will hide the twist, just switch the thread/needle to smaller gauge for those areas, the stitch is fine and well formed, its the fabric that is not thick enough to hide it. Its like your trying to force a big size 10 foot into a size 7 sandal, your toes will hang out the front and heel out the back of the sandal, no way around it, get the right shoe, same principle.

Thank you! 🙏It works!!!💫

THANKS! I’ve changed my leaking shaft seal in less than 1h (engine in the car). Great video!

So..... WRONG

In fact, doing it like that CAUSES air to build in system...duh

E90 is an electronic board error???? But can just be a glitch. Turning it off and on again worked for me?

Great video thankyou for sharing this 👍💜

Thank you so much , the emergency cable worked perfectly on my Siemens washing machine. You saved me both Time and Money 😊👍👌🤘🏻

Was that wrench buried next to it.

Nice.❤❤❤

Any keaks?

I opened the cap of the little tube on the left but water won’t come out 🤦‍♂️

Thank you so much for all your knowledge.👍

I'm always telling people that inanimate objects can't heal. Now they will point to this video and tell me I'm wrong. Of course if the Rocket is actually alive then I'm still right. 😉

guys whats the best lighter form ? I want electric ignition with butane jet flame. what to do.

heat it and hammer it.

USe charcoal..

I’ve been trying to adjust my Juki ddl 8700 for days the same way and nothing works, I even changed needles and needle sizes and nothing works :(

Hello. If i can get a little help. My tumble dryer Bosch serie 4 has a Ph I label, and now the Ph 2 label has appeared. What is that? The machine dries well, all filters are cleaned. That mark appeared when my son pressed something while the machine was running. Anyone? 😊

I like using the Molasses Bath method - no dangerous acid to mess with, just supermarket bought molasses/black treacle

"I would not use sulphuric acid for de-rusting steel, phosphoric acid is much better as it leaves the surface etched with a layer of iron"

That wd40 is useless as a penetrating fluid.

I guarantee you that a more complete yet easy to understand video doesn't exist. I was tempted to send my machine to the bottom of the ocean until finding this. You are a life saver!

Thanks for taking the time to show the results of adjusting the top and bottom tension. Sewing with thicker thread seems to create this problem for me and now its a matter of having patience to adjust.

It's pretty simple but I just watched it again to be sure I remembered correctly. It seems some company's eggs keep longer than others, although I have only two data points!

👍

Ecco perché io pulisco il filtro ogni tre mesi

thank you

It won’t n open after I put it back together , what do I do

Great video

Finaly, somebody explained it so even I understand. Cheers

Thanks. I'll try this, as the only thing that works properly is the clock. Fuel gauge reads accurately, until you turn the engine on, then it jumps up 1/4 tank higher. The oil pressure, engine temp do nothing, and the voltmeter needle constantly vibrates at +/- 14 volts.

I use electrolysis and would prefer vinegar over any real acid simply for ease of disposal and safety. Thinking about a muriatic acid accident gives me nightmares. I'll work a little harder and stress a little less. They all have their applications.

Very nice results!